Відео

Hi, I'm planning on reloading the .308 Winchester with a 190 grain Hornady Sub-X bullet. I have 3 Vithavuori powders available: N120 - N135 - N540 I would like to get around 320 mt/sec. on the Benelli Lupo 1/10" rifle Where do you think we should start?

I'm a cheap ass too...but I have two vises...one for metal, and one for wood that has wood screwed to the inside of the jaws...the wood won't mar up your parts...but you may have to check your tightness every few minutes...never had one come out on me, but always good to make sure a gas block doesn't pop out and dent your forehead...😂

20” barrel?

Dang man that sucks! KAC ain’t cheap either. I’m finishing my build tomorrow with a level I ordered for Xmas (it’s the badger ordnance condition one ACD level). I’m hoping it’s as good as they say. It’s adjustable out of the box so I can adjust it to my rifle and secure it, it also has a space for me to insert tritium vials for night time and low light. I hope it’s good to go. The mount was 320, then I added an accessory mount and ring for a red dot (120 for the ARC, 40 for the ACRO mount), now 120 for their level. At 580 before taxes and shipping my mount is worth more than most people’s red dots alone. It better be good to go. This sucks.

Thanks for the video! Can you share what end cap material you chose? POM or aluminum? I have a Western Aigrun Sidewinder Compact and an AEA challenger Pro, both are bare barrel without any shroud, do you think I should get the high flow core?

Hot fence wire works a lot better

Just got my arp my safety is really really hard to switch

The same Sarissa design in their Accipiter line should drop the POI a lot less since its much lighter than the standard Sarissa.

How do you remove the bolt without a bolt release???? I did just the opposite and bought one without and wanted WITH 😑

I am having the opposite issue. Just built my AR9 Lower kit is BRAVO so not shitty components Safety selector is extremely loose HELP

Imagine having no idea how to swap a gas block, assuming it's easy AF, trying to figure out how to get a too-big roll pin through the too-small roll pin hole, sweating, cussing, crying.....then finding this FREAKING KING on the UA-cams! Bro this video is a panty dropper! Thank you!

Is it ment to Be a micro adjustement, but if it’s free floating up and down that wouldn’t make since

Impulse Air IA-1350 is in my mind the best in every way. I have sevearal rifles and this performs exact same on them all no matter how loud the unmoderated rifle is. All my tests are on .25 cal rifles.

Man your hand was shaking 😮

Mine came with a shade, it’s in the box under the big square cardboard flap on the left.

Agree, 100%

You mentioned a super 22-250, how’d you get there? Twist rate and all the rest. Also, how close to hearing safe is it while supressed?

Thank you!

Hahaha

I have a falx and a sarissa. Both are phenomenal. Impact mkii .25 80ft/lbs - 78db with Sarissa - 82db with the Falx. I’m curious how a Fox 600 over barrel would sound and work. I competed for the first time this year with the Sarissa. Shot a 220. It’s legit.

Too hard to hear you over that 1970’s Kmart music

I watched this video and was interested. I emailed them 2 questions and they never responded. Yes, I checked the spam folder every day. It has been a week now.. not sure I want to purchase this brand if they cannot even answer an email.

What tbac suppressor is that?

Which has a better image? Which has a bigger screen?

Any decibel readings?

What’s better as a handheld scanner to go with my NVGs? The Nox18 or the Nox35? Was thinking the 2x optical base mag might be nice…

Burnt and raw😂😂😂😂😂

I use a toothpick as slave pin to make sure the hole doesn’t get misaligned as I start punching

Blud blew up the piss bottle

Same combination bullet and powder is giving me the following on a 9" barrel. measured by Magneto Speed Sporter. 8.1 grain - 1020 1050 fps tested 10 bullets 8.3 grain - 1050 -1090 fps tested 10 bullets. all loads above 8.5 are super sonic 2.075 " cartridge length case length 1.360" those sub-x bullets vary slightly 190.40grain to 190.80 grains.

Have you had any issues with this trigger? I accidentally bought the one with bolt release too

4 sexond

iin some videos the nox has the white and black, in another almost a blue hue but your video shows warm white. i really prefer the warm color it has in your video can you tell me first hand what the actual hue is when looking through it? thank you very much

I bought the same exact trigger so hey thanks for making this video it does look pretty straightforward and getting rid of the bolt release

Thank you for sharing, this was very helpful!

The 4 2 10 name was coined by Pitmaster X. Pitmaster X made a video of the cook because he was so impressed with this particular cooking method. But the strategy was developed by Steve Gow at Smoke Trails BBQ, and he didn't call it 4 2 10. And for the record, I don't like the name 4 2 10 because it's not really 4 2 10. The timing is dependent on the size of the brisket and some other things. You have to follow the procedure outlined by Steve Gow. It does work because I have done it half a dozen times and it's basically foolproof - provided you follow Steve Gow's strategy.

What is the distance? Sorry I must have missed it.

Bet money you replaced them bulbs in your tail lights shortly after this video lol. Also you need the special 6.5 creedmoor aka magnum bolt and firing pin for that rifle . The 6.5 has a higher case pressure and blows the primers back into the f.p that bends your f.p retainer and causes light strikes. Look at your primers that are going off.

Where’d you got the roll pin starter set?

Bolt carrier group is backwards Dad…😂

I had to buy mine one of those bench mats that has the image blown up and in section!

Bcg is backwards 😂😂😂😂😂😂

He shouldn't be around a firearm 😮

The guy in doors, about how far away from the scope was he? I know the 35 has minimum magnification of 3 something but was wondering how it would fair up real close as well.

That was black piwder not tannerite....otherwise the camera man would be dead!

A good level is hard to find... I'm looking for a nice rail mounted level that has some good reviews (that brought me here), I may have to pay the price (MDT) to get a good one. I ordered a Starrett mini level to help with a scope install and it was trash right out of the box. If you can't trust a high end company like Starrett who can you trust?!?!

The big problem is the Chinese thermal cheap components.

You would think that amount of dip would give any man the strength and confidence to handle the recoil of any rife….. the solution…. ADD MORE DIP!!!!!!!!!!!!!

It's a collapsible stock dummy, use it!

Got some dip in that lip 🤣